alright guys with out further a due, here is a link to the " black box" that 007 was using... or something close to it.  but has it been Modified? not sure?

http://www.newegg.com/Product/Product.aspx?Item=9SIA67038T2564&nm_mc=KNC-GoogleMKP-PC&cm_mmc=KNC-GoogleMKP-PC-_-pla-_-HI+-+LED+Light+Bulbs-_-9SIA67038T2564&gclid=CNWT0ufA3c0CFUVhfgod9v8PlQ&gclsrc=aw.ds

caps in the same place and everything

viking and i have been picking this apart more and more

dont get me wrong, that case could be use for a lot of things, but... even the caps are in the same place inside... so its our best guess

~Russ

wow... 25$... ok ordered...

Can anyone do a thorough search for the ELCAPs used in 007 demo ?

Attached is a near shot of it. I have not been able to find them and check if they are special in any way. They appear larger than what most ELCAPS of 220uF/450V are.

Also attached is a  preliminary image of an overview of the setup with the lamps with the (output) connections highlighted in blue.
What is clear now, is that the output current measured is NOT the current to the bulbs. Instead it looks like it's the coils current and voltage as it appears 10% inductive. It might be though, that one of the traces were inverted , to add to the obfuscation.
Anyway - so it appears that the current to the bulbs is running elsewhere. The effect of them though can be seen by the slight distortion of the voltage waveform as it's at the peaks when they draw the current (see previously posted waveforms).

Isn't it just wonderfull.. ?? :P

more testing, mostly with the HV config, bidirectional.

https://www.youtube.com/watch?v=lUCGOTwkRpI

~Russ

more coil screen shots from 007 demo's

one can see the one coil is different in some slide. some have long leeds some short:

FYI teh coil with the good REZ photos is a cross config coil... so there is only 2 outputs. wire automatically goes back in the coil at the " split"

Hi Russ - I don't know whether this has any bearing or use, but I was experimenting with the Knotplot app & finally got the correct 3D coil configuration - at least I think I did. What I'm noticing is that when I set up 11 formers, the wires don't line up with the slots, but when I use 12, everything lines up perfectly. So in terms of geometry, 11 formers with 24 slots distorts the geometry - maybe only slightly - but with 12 the geometry stays as it is naturally formed. A couple of screenshots attached.

Quote from jrodney55 on July 6th, 2016, 09:13 PM

Hi Russ - I don't know whether this has any bearing or use, but I was experimenting with the Knotplot app & finally got the correct 3D coil configuration - at least I think I did. What I'm noticing is that when I set up 11 formers, the wires don't line up with the slots, but when I use 12, everything lines up perfectly. So in terms of geometry, 11 formers with 24 slots distorts the geometry - maybe only slightly - but with 12 the geometry stays as it is naturally formed. A couple of screenshots attached.

I think so ,  I made a STL file with 12 Formers for those who want to test, click the link below

https://drive.google.com/file/d/0B3PEt_f3pr2wdmN3MzRLLW5jREk/view?usp=sharing

nice work Jim,

can you post that screen shot of the program and the coils. so we can explain to others that there are Manny other individual coils when doing it 12x12

this i understand but others might not, so to briefly explain it, the reason we don't use 12 former's is that the circuit would need to " jump" a loop every time through the torus...  hope this makes since... its basically a way to make the coil easier. however it is not the same as the math when done this way...

more coil testing this morning and coupling coils together as well.

https://www.youtube.com/watch?v=rawtCA0iBVo

just trying stuff out.

~Russ

from the video i just posted:

here's one for ya

???

comments please...

Hey Russ, nice setup you have there, really enjoying watching your progress. Any ozone production while achieving output voltage like that? I dont have a scope but when Im in the 300-500v output range I get hissing and a very strong ozone smell. The coupling between the coils is fascinating.

hey, welcome Joe, so i don't get hissing or ozone ( not that i can smell ) but do get a nice buz from the coil. i think i smelt some ozone but not much, not like i would think, that could be due to the coil configuration. and wiring setup.

you say 300-500V is that RMS voltage? if using DMM i would say yes. ???

also feel free to share your experience more. i know you have played with theses a lot.



geg,  thanks for the files. like i was saying before if you use 12 you will be more on par with the math, however you will end up with Manny more coils ( 6 or 12 to be correct) and that is why we use the 11, it makes for a single wind around the torus.

~Russ

 
Congrats Russ.

I tested a small starship coil and came out with analog and digital values over unity on June 22
with no amplifier using 5 - 6 volts DC only. 

Should post it soon having the event on video but have been thinking. I am 99% sure but a bit
more testing would would enhance the confidence level.

The hardest part is to get people to believe the coil... most are locked in their boxes in their space
and do not hear or accept the results.

 





     

by the way this is old but might be helpful to understand the "simple" complexity of how the math works with the coil.

http://rwgresearch.com/open-projects/vortex-base-math-research/the-math/

http://open-source-energy.org/rwg42985/russ/Russell_Gries%27s_perspective%20_on_the_activation_sequence_of_the_ABHA_torus_using_electricity.pdf

~Russ

Quote from talisman on July 7th, 2016, 04:25 PM

Congrats Russ.

I tested a small starship coil and came out with analog and digital values over unity on June 22
with no amplifier using 5 - 6 volts DC only. 

Should post it soon having the event on video but have been thinking. I am 99% sure but a bit
more testing would would enhance the confidence level.

The hardest part is to get people to believe the coil... most are locked in their boxes in their space
and do not hear or accept the results.

welcome,

thanks for the feed back,

please tell me how you were measuring the coil.  and with what meters / scope.

also a simple schematic would be good.

thanks for sharing your results! 

~Russ

FYI, if you click the reply near the top or bottom of the post's you can attache images...

hey, you managed to drop the question marks on the scope...thats a good sign, right?!  theres a lot going on in that scope shot so its kind of tough to see. ill try your arrangement tonight.
a thought: is there any way for you to power the amp and everything via a DC to AC inverter so the entire system will run from battery? i didnt pay close enough attention to how you were powering your signal generator etc. my thought is that the entire rig could be measured at idle then powered up and you would know the DC draw from the battery pack. yes, it would still be possible to claim 'battery effect', but it would knock down one more door for ya. maybe one of us can start getting results like you and you wont feel like such a marionette   :)
love the OSD

Quote from jeremy gwilt on July 7th, 2016, 04:43 PM

hey, you managed to drop the question marks on the scope...thats a good sign, right?!  theres a lot going on in that scope shot so its kind of tough to see. ill try your arrangement tonight.
a thought: is there any way for you to power the amp and everything via a DC to AC inverter so the entire system will run from battery? i didnt pay close enough attention to how you were powering your signal generator etc. my thought is that the entire rig could be measured at idle then powered up and you would know the DC draw from the battery pack. yes, it would still be possible to claim 'battery effect', but it would knock down one more door for ya. maybe one of us can start getting results like you and you wont feel like such a marionette   :)
love the OSD

yeah, so im not worried about the power consumption of the generator / amp at the moment.

like Matt said a while back there is a golden circuit ( or so it looks) with the push pull with clamping. high effencty driver / gen... then we can worry about the draw. at that point ill run it off a solar cell. lol then i can claim no battery effect and measure true input lol   

but yes, at some point we will need to set it up like that. right now i'm not trying to convenience any one of OU i'm trying to find the best way to run / connect / wire this coil...

i will be going back and trying this test again and document it better and make sure everything is correct. i feel it was measurements.

any how looking forward to your testing in that config.

still cool to see that much power being transferred between that coil and cap but not where the amp input is. its all in the coil / cap.

~Russ

Quote from ~Russ on July 7th, 2016, 04:38 PM

by the way this is old but might be helpful to understand the "simple" complexity of how the math works with the coil.

http://rwgresearch.com/open-projects/vortex-base-math-research/the-math/

http://open-source-energy.org/rwg42985/russ/Russell_Gries%27s_perspective%20_on_the_activation_sequence_of_the_ABHA_torus_using_electricity.pdf

~Russ

because i know you wont go watch them there ill post them here:
this was old, but still helpful to understand how the wire is laid according to the math.

https://www.youtube.com/watch?v=4lQhuXzIJgQ

https://www.youtube.com/watch?v=ACxx-7L1RaE

https://www.youtube.com/watch?v=Ko3frb8G14w

~Russ

oh hell ya.....air core with about a cm between windings and it still transfers that well? thats unheard of from where im sitting. i was inputting 2 mA  @ 6v  .... 2 milliamps! and still getting over 1 mA @6v returning in the pickup coil.
to be sure, it is quite an amazing configuration.

load connected to the cap?

I am out of town now so I have to get my stuff. I used a mastercraft multimeter for volts and an innova automobile mutimeter for amps with the digital readings. No scope. The amperage for analog was done with a couple of new 10 amp panel meters. The voltage difference was not so significant. The first happening was using a single 6 volt lead acid battery run down to about 5.5 volts.

Later I got better results with a simular power range AC adapter but want try another adapter the very same in case of damage as the input on the adpter was 6.15 open ended while I think the other 4 I have put put about 6.46 volts at maximum 1.2 amp. I trust the readings at this time but want to see more physical evidence, such as more power lifting a wheight.

Holding small motors to max amp had more torque than the adapter alone.

For the control the input was much the same without the coil and the output was not increased.

I will try to post a small diagram later tonight it is really simple but I am on the run.

I think (hypothesis) that this coil found some resonance with a DC light along with the motor befor the motor alone.

                                           
               

My set up is very modest, I have a POE heavy cross pattern coil from 1stopenergies. 1000v .15uf caps (250v caps exploded) 2 DMM (RMS measurements), audio amplifier, use F generator iphone app (limited to 20khz), various loads. The circuit I find works best is the same as what Russ posted. I have also wound Bifillar pancake coils as a receiver coil with pretty good results but nothing close to the coupling I just saw in Russ's video. 300V and up i get massive ozone hiss and smell, i think its from the cross pattern. I know Daniel Nunez encased his in resin to eliminate this and have seen others submerge it in oil. Over Unity measurements with a meter are easily achievable and was very happy to see some confirmation in the scope measurements. There are also interesting effects when you spin magnets near the center and the system draws less wattage. Another interesting note is when I put my pancake coil on top of the vortex coil open ended it will all run fine but if i short the pancake coil the whole circuit will short out as if the pancake coil is wired to the vortex coil. The point is these vortex coils magnetic/electric fields are very much part of the circuit. I do believe the ultimate overunity test would be  DC>PWM>COIL+CIRCUIT>RECTIFIER>DC

Heres my coil and a picture of a HPS bulb with an interesting arc in the bulb. I could shrink or grow the frequency of the pulses with a magnet and move it around the tube.

If the coil works in resin then the source of the additional power amplification can pass through a solid inert
material as a core...  transformation. I was going to try this to see if it still worked in epoxy yet the resonance
would  have thought needed air space for harmonic vibe.

now this thred is going some where. Nice work everyone. Keep up the testing and sharing results. I will be going back and doing a better documentation on my testing. Currently just testing everything and seeing what seems to work for what. Then I'll dig deeper. Good thing is that everything is recorded on the live stream....

~Russ

Quote from talisman on July 7th, 2016, 10:40 PM

If the coil works in resin then the source of the additional power amplification can pass through a solid inert
material as a core...  transformation. I was going to try this to see if it still worked in epoxy yet the resonance
would  have thought needed air space for harmonic vibe.

I don't think that coil resonance relates to harmonics / sound.  I believe it more likely relates to how the energy moves around the coil - ie at certain frequencies the energy hits a harmonious pulse which spins up a good 'tornado' shaped energy field around and through the torus