The Rodin Coil Over Unity Energy Amplifier. Russ's Work

Matt Watts

High-res STLs
« Reply #53, on June 4th, 2016, 01:16 PM »
Try to use the non "A" version ring first if it will work.

3D Builder seems to have a problem with the ring as exported from IronCAD.  After fixup the file is smaller--probably reduces resolution.

jeremy gwilt

Re: The Rodin Coil Over Unity Energy Amplifier. Russ's Work
« Reply #60, on June 4th, 2016, 05:46 PM »
you guys are killing me! i think i have to start repairs tonight on my printer (if i fail...then it can be rebuilt for pcbs mwahaha)
that is some tight modeling! very nice work

~Russ

Re: The Rodin Coil Over Unity Energy Amplifier. Russ's Work
« Reply #61, on June 4th, 2016, 06:26 PM »
Well. Power keep flickering killing my priemter. Even tho it's connected to a ups.

And.

This is a bit to close for comfrent.

Less than a mile

Ash falling down. Wind blowing this way. You know. All the fun stuff

Car packed.

Ready to roll of need be.

~russ

Matt Watts

Re: The Rodin Coil Over Unity Energy Amplifier. Russ's Work
« Reply #68, on June 5th, 2016, 02:22 AM »
Man, I watched this again:

https://www.youtube.com/watch?v=Q6BC8mT5fFk

And I just do not see the crisscross pattern that Daniel uses.

007 said it does not work with induction so I'm thinking L1/L2 is actually more like a common mode choke arrangement instead of a transformer.


Russ, be careful buddy.  If you have to bail on this project for a while, I'll run with it best I can.  Marko is counting on somebody getting this replicated and legitimized.  Whatever it takes, we'll find a way.

Gunther Rattay

Re: The Rodin Coil Over Unity Energy Amplifier. Russ's Work
« Reply #69, on June 5th, 2016, 03:00 AM »
If Marko wants it to be replicated the best way to start is to work on his original configuration he has.

Getting all details by observation and then start replication.
If he´s in the states that should be not too much of a problem ...

jeremy gwilt

Re: The Rodin Coil Over Unity Energy Amplifier. Russ's Work
« Reply #70, on June 5th, 2016, 07:47 AM »
version 9 ring printed last night....the stars aligned for me and repairs went well   :)
ill start prining forms today....but somebodys gotta show me how to wind this crazy thing  !

~Russ

Re: The Rodin Coil Over Unity Energy Amplifier. Russ's Work
« Reply #72, on June 5th, 2016, 09:04 AM »Last edited on June 5th, 2016, 09:07 AM
Yes Matt. Thsts what I have been trying to stress. It's not cross pattern.

Im all game for this. Funds should be on the way to buy the wire.

And I have 22 or 24 in stock. Just don't known if it's enugh.

Yeah it's a combo. Not just a transformer. But a type of choke. Too ?? I don't know. :)

Gunther. I think have all the details we need.

Nice work jermy.

You know why that happen. Its because of you would have started printing that night. You would have to restarted.  Cuse it was all wrong.

The universe was stoping you for a reassion. :)

Ok. I'll be back home later and restart the ring. With holes. :)

~Russ.

Oh. One more thing.

Matt. The ring , the slight bevel on the small tab is beveld the wrong way. It needs to bevel in the center. Not point out. :)  it's inverted. Also make it about .5mm shorter. Should fit really nice. You get that done in then next hr or so I'll be able to make that version. :)