open-source-energy.org

Open - Source - 3D Printing => RepRap, 3D Extruder, 3D Printing => Topic started by: cncjoe on February 15th, 2013, 12:38 AM

Title: Printed part quote
Post by: cncjoe on February 15th, 2013, 12:38 AM
Hey, I was wondering if someone here could print me up one of these http://www.thingiverse.com/thing:18379 or just the herringbone gears?
If it's much more than around $80 though I'd rather try retrofitting the wire drive from a mig welder like this ebay(http://www.ebay.com/itm/Clarke-180EN-MIG-Welder-Complete-Wire-Feeder-Parts-/170620750282?pt=LH_DefaultDomain_0&hash=item27b9ca09ca)
Thanks!
joe
Title: RE: Printed part quote
Post by: ~Russ on February 15th, 2013, 01:28 AM
Quote from cncjoe on February 15th, 2013, 12:38 AM
Hey, I was wondering if someone here could print me up one of these http://www.thingiverse.com/thing:18379 or just the herringbone gears?
If it's much more than around $80 though I'd rather try retrofitting the wire drive from a mig welder like this ebay(http://www.ebay.com/itm/Clarke-180EN-MIG-Welder-Complete-Wire-Feeder-Parts-/170620750282?pt=LH_DefaultDomain_0&hash=item27b9ca09ca)
Thanks!
joe
hey joe, send firepinto or Jeff Nading a message. that would be extremely cheep to print. they probably would be glad to help. i would be glad to help also but i haven't finished my printer... :)

~Russ
Title: RE: Printed part quote
Post by: Jeff Nading on February 15th, 2013, 07:30 AM
Quote from cncjoe on February 15th, 2013, 12:38 AM
Hey, I was wondering if someone here could print me up one of these http://www.thingiverse.com/thing:18379 or just the herringbone gears?
If it's much more than around $80 though I'd rather try retrofitting the wire drive from a mig welder like this ebay(http://www.ebay.com/itm/Clarke-180EN-MIG-Welder-Complete-Wire-Feeder-Parts-/170620750282?pt=LH_DefaultDomain_0&hash=item27b9ca09ca)
Thanks!
joe
Good morning Joe, believe it or not, the parts you are asking for I have already printed, two extruder sets, one used, one new. Send me an email with your address.:D
Title: RE: Printed part quote
Post by: cncjoe on February 15th, 2013, 06:24 PM
Quote from ~Russ/Rwg42985 on February 15th, 2013, 01:28 AM
Hey joe, send firepinto or Jeff Nading a message. that would be extremely cheep to print. they probably would be glad to help. i would be glad to help also but i haven't finished my printer... :)

~Russ
Thanks Russ. I surprised your not up and running yet! Seems like when you get your teeth into something you don't let go till it's done. Good luck with your build!
joe

Quote from Jeff Nading on February 15th, 2013, 07:30 AM
Good morning Joe, believe it or not, the parts you are asking for I have already printed, two extruder sets, one used, one new. Send me an email with your address.:D
Thanks so much Jeff! I sent it to you. I looked in your ebay store and didn't see any. Don't you sell them there?
joe
Title: RE: Printed part quote
Post by: Jeff Nading on February 15th, 2013, 06:38 PM
Quote from cncjoe on February 15th, 2013, 06:24 PM
Quote from ~Russ/Rwg42985 on February 15th, 2013, 01:28 AM
Hey joe, send firepinto or Jeff Nading a message. that would be extremely cheep to print. they probably would be glad to help. i would be glad to help also but i haven't finished my printer... :)

~Russ
Thanks Russ. I surprised your not up and running yet! Seems like when you get your teeth into something you don't let go till it's done. Good luck with your build!
joe

Quote from Jeff Nading on February 15th, 2013, 07:30 AM
Good morning Joe, believe it or not, the parts you are asking for I have already printed, two extruder sets, one used, one new. Send me an email with your address.:D
Thanks so much Jeff! I sent it to you. I looked in your ebay store and didn't see any. Don't you sell them there?
joe
All I have listed are the kits no individual parts. And just need to make this clear not selling anything here.
Title: RE: Printed part quote
Post by: cncjoe on February 15th, 2013, 08:24 PM
Quote from Jeff Nading on February 15th, 2013, 06:38 PM
All I have listed are the kits no individual parts. And just need to make this clear not selling anything here.
Oops. Have I crossed some line?:blush:
Title: RE: Printed part quote
Post by: Jeff Nading on February 15th, 2013, 08:36 PM
Quote from cncjoe on February 15th, 2013, 08:24 PM
Quote from Jeff Nading on February 15th, 2013, 06:38 PM
All I have listed are the kits no individual parts. And just need to make this clear not selling anything here.
Oops. Have I crossed some line?:blush:
No, it's just so no one will get the wrong idea, no problem Joe.:D
Title: RE: Printed part quote
Post by: ~Russ on February 15th, 2013, 08:38 PM
Quote from cncjoe on February 15th, 2013, 08:24 PM
Quote from Jeff Nading on February 15th, 2013, 06:38 PM
All I have listed are the kits no individual parts. And just need to make this clear not selling anything here.
Oops. Have I crossed some line?:blush:
;)

Nagh, Jeff just wanted to be clear with everyone else that he dose not "advertise" here on this site. ;)

What your asking for is a part that is "open sorce" and that's a good part of this forum is to be able to find stuff that is open sorce and Find someone like Jeff was willing to create it for you ;)

~Russ

Nice work guys it's excellent when a plan comes together :-)