Pulse Motor Build off 2014 Final 3min Entry videos! Post Here

~Russ

Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« on November 13th, 2014, 01:57 PM »Last edited on November 13th, 2014, 02:09 PM
Post your PMBO final entry's here. remember no more than 3 min is allowed (  video length not including the 30 second intro video if you chose to include it in your entry, you can find the intro video HERE

Good Luck!

( This thread will be locked after the contest entry time)

Diadon

Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #1, on November 15th, 2014, 05:47 PM »
Looking forward too it :)

TommeyLReed

Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #2, on November 18th, 2014, 05:19 PM »Last edited on December 5th, 2014, 03:43 AM
:s

Tom

Twoodroof


skycollection


~Russ


deeds

Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here - Deeds Test
« Reply #6, on December 12th, 2014, 02:00 AM »
Quick test post ...currently working hard to finish. cheers

natsud1

Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #7, on December 12th, 2014, 12:20 PM »Last edited on December 12th, 2014, 12:53 PM by ~Russ
Finally....here is my entry,Thanks everyone.
Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #8, on December 12th, 2014, 12:21 PM »Last edited on December 12th, 2014, 12:23 PM by Lynx
well That didnt seem to work... maybe this will. 


https://www.youtube.com/watch?v=Asc_QYqs-Xo#ws

Mister Caribbean Roots

Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #9, on December 12th, 2014, 02:43 PM »Last edited on December 12th, 2014, 02:46 PM
Hi everyone,

PMBO 2014 - First Entry,
The Flux Gate Generator setup has been completely modified for the PMBO so that i do have a entry that does run with far less input and far better output...^^
For them judges...since i'm running the DC motor with a PWM i don't know if that's against the rules or not but if that's that case than you may disqualify it...it's no problemo...;-)
At the end of video are 3 pictures...;-)
Good luck everyone and remember to have fun...having fun and learning at the same time is of much more importance than to win... :clap: :excited: :clap2:


https://www.youtube.com/watch?v=qj9E6wtcGlI#ws
Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #10, on December 12th, 2014, 02:45 PM »
Hi everyone,

PMBO 2014 - Second Entry,
This is my second entry just in case the first one gets disqualified since i'm being lazy and running the DC motor with a PWM...lol... :P
At the 2.29 min mark it sound like i said "max of 200ma" but i said "max to 100ma" but since i talk funny it sounded like 200ma...lol
At the end of video are 3 pictures...;-)
Good luck everyone and remember to have fun...having fun and learning at the same time is of much more importance than to win... :clap: :excited: :clap2:


https://www.youtube.com/watch?v=autinZjf_l8#ws
Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #11, on December 12th, 2014, 02:53 PM »
Quote from deeds on December 12th, 2014, 02:00 AM
Quick test post ...currently working hard to finish. cheers
Hey mate,
You can do this, if i was anywhere near you i would drop by to help you out... :earthhug:
I only ask for a few things...a nice lab coat as yours to wear and a slice of cake and hot choco... :giggle: :excited:

Looking good everyone...keep it up... :cheerleader:

Andreas


Luque

Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #13, on December 13th, 2014, 03:23 PM »
My entry this year.


https://www.youtube.com/watch?v=e53yls84Ees#ws

It was fun to build it even though things didn't work as expected.

Alberto

Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #14, on December 13th, 2014, 03:51 PM »Last edited on December 14th, 2014, 06:24 AM
Hi all,

Some years ago i tried to make a magnetic-motor
but all the results were negative.
Inspired by the pulsemotor challenge i took (much too late),
the rotor that was left, out of the garage.
Well i didn`t a great job like other people did here,
but i send this because i was amazed that i got
the rotor running with so less components.
Just a battery, a cheap coil, and a reed-switch.
First i used a power-supply, but today I took
an old battery (12V) that i hadn`t used for more
than one year. When i started the power was
very low, but it seemed that the system was
helping the battery to raise power.
It`s too short time to do some tests, what is better...
I had it running with and without a fly-back diode(LED).
Anyway, i hope i inspire other people to do tests with the
system. (It`s not new, many other people did it before)
Maybe it`s the road to free-energy...
Regards Alberto.

Update: After running 24h voltage has gone down to 9,75V :(


https://www.youtube.com/watch?v=SFASFVZgBs8#ws

Slider2732

Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #15, on December 13th, 2014, 05:55 PM »
Here's my entry...  :)
The Linear Light Engine

1.5V linear pulse motor.
Features a bifilar coil, constant light output when tuned and no need for a biasing magnet.
The video shows the circuit diagram and then the initial set up. The result is the running motor at the end.



https://www.youtube.com/watch?v=FAhVC0HnJ94#


HHO4Life

Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #16, on December 13th, 2014, 11:45 PM »
FSRD PMBO Entry Video...

My video has been uploading to YouTube from my phone so I don't have a link to it yet.

I was unable to finish it I didn't have much time and have been waiting for parts to get here some still haven,t arrived but this is what I have. I will post a video of the completed design as soon as it is complete.

As soon s I have the link I'll post the link to the entry video.

Limitless


HHO4Life

Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #18, on December 14th, 2014, 01:45 AM »
OK my video is finally done uploading to YouTube... Here it is, it may still be processing but should be available anytime now:


https://www.youtube.com/watch?v=mmxP0lKS498#

firepinto


skycollection


jeremy gwilt

Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #21, on December 14th, 2014, 08:17 AM »Last edited on December 14th, 2014, 02:41 PM
hey all...good to see some 'out of the box' stuff out there!

i didnt include power measurements in my video. sorry, i was in rough shape and couldnt pull it off in under 3 minutes....haha! quite a few things came up during the build that i want to go back and look at again....one for sure being the efficiency of these air-core (plastic tube core?!) coils that are driving the HV transformer.
my apologies to anyone genuinely interested in the hho / faraday cage build. i am interested as well, but wanted something that somewhat functioned to enter.

measurements are taken with leds removed from the generator coils.

input voltage: 19.8v
input current (2 oscillating coils): 108mA
input current (all six drive coils+sensors): 550mA

output voltage: (2 oscillating coils): 10.6v
output current: (2 oscillating coils): 120mA

output voltage: (all six drive coils+sensors): 12.05v
output current: (all six drive coils+sensors): 135mA


https://www.youtube.com/watch?v=TOYIZ3aPu1U#ws

deeds

Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #22, on December 14th, 2014, 03:08 PM »
Hey gus, it's 23:03.. the final hour, I'm shattered but... I made it!  My first PMBO, my first year learning about the art.
Please find my final "fun SlayDini" entry for the competition. Nailed it, now I can go put my feet up for a bit.


https://www.youtube.com/watch?v=4f_FijngcH0#ws

Awesome, well done to everyone and good luck.
Deeds

TommeyLReed

Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #23, on December 14th, 2014, 04:19 PM »Last edited on December 14th, 2014, 04:38 PM
Hi All,

This is my radial pulse motor generator entry.
 3 minutes is short time to talk about this motor, but they are the rules.


https://www.youtube.com/watch?v=2bWRBHvb6mM#ws

Spec:
Radial Pulse Engine/motor/generator
Input 12v@3a max (motor input), stall load 56w
Input 9v@ 40ma (micro controllers)
8 coils 24 gauge at 100 ft each (2.567ohms)
PWM speed controller
1 Arduino 2560 mega
ECM reading/controls
Rotational 5 degree steps (72 steps per complete rotation)
Control firing power stoke on each piston coil 0deg(TDC) to 180deg(BDC)
8 led piston firing lights
RPM reading (0- 3600)
Output:
BEMF collector from 8 coils


Good luck to everyone, some real good builds out there :cheerleader:
TLR

mnsman

Re: Pulse Motor Build off 2014 Final 3min Entry videos! Post Here
« Reply #24, on December 14th, 2014, 07:30 PM »Last edited on December 15th, 2014, 05:13 AM
I had a fun time putting it all together.  Looking forward to jazzin it up some more.  Well done everyone and best of luck. 


https://www.youtube.com/watch?v=Pt5Ly9ryw4Y#ws